Sizes of wheel nuts of Aston Martin V8 Vantage

home ⇒ equipment ⇒ wheel fastener ⇒ aston martin

For the V8 Vantage model, the wheel is attached to the hub using wheel nuts. The number of fasteners depends on the V8 Vantage year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 5;
  • Fastener size: from 1/2in20UTF to M14x2.0;
  • Diameter of the mounting holes (PCD): from 114.3 to 120.6;
  • Disc offset (ET): from 69.10 to 73.80.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel nuts of Aston Martin V8 Vantage
General view spravka
General view

N spravka
Number of fasteners per hub for Aston Martin V8 Vantage.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions nuts

(General view)		5from 1/2in20UTF to M14x2.0from 114.3 to 120.6
Size tables of wheel nuts of Aston Martin V8 Vantage
Years spravka
Year of manufacture or modification of the V8 Vantage

n spravka
Number of fasteners per hub for Aston Martin V8 Vantage.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
199051/2in20UTF120.673.80
198951/2in20UTF120.673.80
198851/2in20UTF120.673.80
198751/2in20UTF120.673.80
198651/2in20UTF120.673.80
198551/2in20UTF120.673.80
198451/2in20UTF120.673.80
198351/2in20UTF120.673.80
198251/2in20UTF120.673.80
198151/2in20UTF120.673.80
198051/2in20UTF120.673.80
197951/2in20UTF120.673.80
197851/2in20UTF120.673.80
197751/2in20UTF120.673.80
4.3i
20075M14x2.0114.369.10
20065M14x2.0114.369.10
20055M14x2.0114.369.10

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.


0 Comments