Sizes of wheel nuts of AM General Hummer

home ⇒ equipment ⇒ wheel fastener

For the Hummer model, the wheel is attached to the hub using wheel nuts. The number of fasteners depends on the Hummer year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: from 6 to 8;
  • Fastener size: from 9/16"-18UNF to M14x1.5;
  • Diameter of the mounting holes (PCD): from 139.7 to 165.1;
  • Disc offset (ET): from 10 to 50.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Audi
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 5from 14x1.5 to M14x1.5
Possible fastener sizes for all Audi vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
5M14x1.511257.10
4M14x1.510857.10
xM14x1.5xx
xM12x1.5xx
4M12x1.510057.10
414x1.510840
414x1.510837
5M14x1.510057.10
5M14x1.511266.60
5M14x1.513071.60
5M14x1.513073.00
5M14x1.511245
5M14x1.511250
5M14x1.511241
5M14x1.511235
5M14x1.511240
5M14x1.511233
5M14x1.511237
4M14x1.510837
4M14x1.510835
4M14x1.510845
5M14x1.511239
5M14x1.511243
5M14x1.511242
5M14x1.511234
5M14x1.511236
5M14x1.511238
5M14x1.511220
5M14x1.511221

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Audi by models:

0 Comments