Sizes of wheel bolts of Bedford Rascal

home ⇒ equipment ⇒ wheel fastener

For the Rascal model, the wheel is attached to the hub using wheel bolts. The number of fasteners depends on the Rascal year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: -;
  • Fastener size: M12x1.5;
  • Diameter of the mounting holes (PCD): -;
  • Disc offset (ET): -.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for BMW
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 5from 12x1.5 to M15x1.25
Possible fastener sizes for all BMW vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
5M14x1.2512072.60
5M12x1.512072.60
5M14x1.2511266.60
5M12x1.512057.10
4M12x1.510057.10
5M12x1.5120x
4M12x1.510072.60
5M14x1.2512066.60
5M12x1.512074.10
5M14x1.512072.60
5x12040
5x12045
5M14x1.2512074.10
5M14x1.512074.10
xM12x1.5xx
512x1.512038
512x1.512020
5M12x1.512010
5M12x1.512015
5M12x1.512014
5M12x1.512040
5M12x1.512047
5M12x1.512049
5M14x1.2511247
5M14x1.2511252
5M14x1.2511254
5M14x1.2511257
5M14x1.2512040
5M14x1.2512043
5M14x1.2512045
5M14x1.2512034
5M14x1.2512036
5M14x1.2512037
514x1.2512030
5M12x1.512022
5x12044
5x12042
5x120x
5x12035
5x12043
5x12053
5x12047
5x12049
5x12052
5x12034
5x12030
5x12031
5x12037
5x12036
5x12020
5x12050
5x12041
5x12046
5x12017
5M12x1.512020
5M12x1.512018
5x12026
5x12019
5x12032
5x12022
5x12014
5x12018
5x12025
5M14x1.2512025
5M14x1.2512030
5x12013
5x12024
5x12015
5M12x1.512013
5x11243
5M12x1.512041
5M12x1.512012
512x1.512025
512x1.512072.6
514x1.2511226
5M12x1.512023
514x1.512072.6
5x12072.6
5M14x1.2512027
5M14x1.2512029
5M14x1.2512046
5M14x1.2512048
5M12x1.512046
5M12x1.512029
5M14x1.2511225
5M14x1.2511227
5M14x1.2511230
5M14x1.2511239
5M14x1.2511241
5M14x1.2511250
5M14x1.2511251
5M15x1.2511232
5M15x1.2511236
5M15x1.2511235
5M12x1.512031
5M12x1.512034
5M12x1.512036
5M12x1.512037
5M14x1.2511232
5x11230

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener BMW by models:

0 Comments