Sizes of wheel nuts of BYD S6

home ⇒ equipment ⇒ wheel fastener

For the S6 model, the wheel is attached to the hub using wheel nuts. The number of fasteners depends on the S6 year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 5;
  • Fastener size: M12x1.5;
  • Diameter of the mounting holes (PCD): 120;
  • Disc offset (ET): 60.10.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Chery
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 6from M12x1.25 to М12х1.5
Possible fastener sizes for all Chery vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
4M12x1.510057.10
5x10838
4x10038
4M12x1.5114.356.10
4M12x1.5114.356.60
5M12x1.2510856.10
5M12x1.510867.10
4M12x1.2510056.10
4M12x1.5114.371.60
4M12x1.5114.369.10
5M12x1.5114.360.10
5M12x1.510860.10
4M12x1.5114.357.10
5M12x1.510865.10
4M12x1.2510057.10
xМ12х1.5xx
5M12x1.5114.333
5M12x1.5114.345
6M12x1.5139.7110.20
5x10847
5x114.347
5M12x1.510843
4M12x1.5114.346
6M12x1.5139.7106.10
4M12x1.5114.339
4M12x1.2510046
4x100x
4M12x1.510054.10
5M12x1.510837
5x10833
6M12x1.5139.735
6M12x1.5139.767.10
xxx45
6M12x1.5139.7x

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Chery by models:

0 Comments