Sizes of Ford wheel fastener - Dimension tables

Sizes of wheel bolts of Fiat X1-9

For the X1-9 model, the wheel is attached to the hub using wheel bolts. The number of fasteners depends on the X1-9 year of manufacture and is presented in the table below.

Total dimensions of fasteners:

Number of fasteners: -;
Fastener size: M12x1.5;
Diameter of the mounting holes (PCD): -;
Disc offset (ET): -.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing

General parameters of wheel fastener for Ford

General view General view	N Number of fasteners per hub for marka. Measured in pieces.	Size Metric size of fasteners: Thread M14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.
(General view)	-	from 4 to 8	from 1/2-20UNF to M14x2.0

Possible fastener sizes for all Ford vehicles

N Number of fasteners per hub for marka. Measured in pieces.	Size Metric size of fasteners: ThreadM14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.	ET (mm) Disc offset: Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.
5	1/2in20UTF	114.3	70.60
4	M12x1.5	108	63.30
4	M12x1.5	100	54.10
4	M12x1.5	108	63.40
5	1/2in20UTF	139.7	86.70
5	1/2in20UTF	114.3	93.10
5	M12x1.5	108	63.40
x	M12x1.5	x	x
5	1/2in20UTF	114.3	70.10
5	M14x1.5	108	63.40
5	1/2in20UTF	114.3	63.40
5	M12x1.5	114.3	67.10
4	M12x1.5	100	63.40
6	M12x1.5	139.7	93.10
6	1/2in20UTF	139.7	93.10
8	M14x2.0	170	125.00
6	M14x2.0	135	87.10
5	M14x2.0	135	87.10
5	M12x1.75	135	87.10
6	M14x1.5	135	87.10
5	1/2in20UTF	139.7	87.10
5	x	114.3	x
5	x	114.3	36.5
5	1/2in20UTF	114.3	67.10
5	M12x1.5	114.3	63.40
4	M12x1.5	108	67.10
5	M14x1.5	108	57.10
5	M14x1.5	112	57.10
5	M12x1.5	112	38
4	M12x1.25	108	58.10
4	M12x1.25	98	58.10
4	M12x1.5	98	63.40
4	x	100	45
5	x	114.3	50
6	M12x1.25	139.7	100.00
5	M14x1.5	114.3	70.10
4	1/2in20UTF	108	63.40
4	M12x1.5	108	41
5	M12x1.5	114.3	60.10
6	1/2in20UTF	139.7	70.60
5	M12x1.5	112	49.5
5	M14x2.0	160	65.10
5	M14x1.5	160	65.10
5	M12x1.5	160	65.10
5	1/2in20UTF	108	63.40
5	x	108	x
4	x	108	47
4	x	108	45
4	x	108	40
4	x	108	x
4	x	108	37
4	x	108	35
4	x	108	52
5	x	108	48
5	x	108	52
5	x	108	50
5	1/2in20UTF	114.3	73.10
5	x	160	60
5	x	108	47
5	x	108	45
4	x	108	49
5	x	112	55
5	x	114.3	40
6	x	139.7	40
5	M12x1.5	114.3	40
5	1/2in20UTF	114.3	63.30
4	1/2in20UTF	114.3	63.30
8	M14x1.5	170	124.90
8	M14x2.0	170	124.90
8	M14x2.0	200	160.00
8	M14x2.0	170	160.00
8	M14x1.5	200	124.90
8	M14x1.5	170	160.00
5	M12x1.5	108	50
5	M12x1.5	108	52.5
8	1/2in20UTF	165.1	87.00
5	1/2in20UTF	139.7	87.00
8	1/2in20UTF	165.1	123.90
5	1/2-20UNF	139.7	5
5	1/2-20UNF	139.7	16
5	x	114.3	2
5	x	114.3	36
4	M12x1.5	108	37.5
4	M12x1.5	108	42.5
5	x	114.3	3
4	M12x1.5	108	47.5
5	1/2in20UTF	114.3	x
5	M12x1.5	114.3	70.10
5	M14x1.5	108	52.5
5	M12x1.5	108	45
4	M12x1.5	108	32.5

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Ford by models:

0 Comments