Sizes of wheel гаек of GAZ 52

For the 52 model, the wheel is attached to the hub using wheel гаек. The number of fasteners depends on the 52 year of manufacture and is presented in the table below.

Total dimensions of fasteners:

  • Number of fasteners: -;
  • Fastener size: M20x1.5;
  • Diameter of the mounting holes (PCD): -;
  • Disc offset (ET): -.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).



General parameters of wheel гаек of GAZ 52
General view spravkaGeneral view wheel fastener Quantity (units) spravka
Number of fasteners per hub for GAZ model.

Dimensions (mm) spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
General view spravka
Type of wheel fastener:

For fastening of wheels or discs, 2 main types of fasteners are used:

-wheel bolts;
-wheel nuts.

Dimensions гаек
(чертеж гаек)
- M20x1.5 Гайка
Size tables of wheel гаек of GAZ 52
Year Quantity (units) spravka
Number of fasteners per hub for GAZ model.

Dimensions (mm) spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
PCD (mm) spravka
Diameter between fasteners:

Diameter of the circle on which the mounting holes are located for GAZ model.

spravka
ET (mm) spravka
Disc offset:

1. The distance between the vertical plane of symmetry of the wheel and the plane of contact of the disk to the hub.

spravka
Гайка
1964xM20x1.5xx
1965xM20x1.5xx
1966xM20x1.5xx
1967xM20x1.5xx
1968xM20x1.5xx
1969xM20x1.5xx
1970xM20x1.5xx
1971xM20x1.5xx
1972xM20x1.5xx
1973xM20x1.5xx
1974xM20x1.5xx
1975xM20x1.5xx
1976xM20x1.5xx
1977xM20x1.5xx
1978xM20x1.5xx
1979xM20x1.5xx
1980xM20x1.5xx
1981xM20x1.5xx
1982xM20x1.5xx
1983xM20x1.5xx
1984xM20x1.5xx
1985xM20x1.5xx
1986xM20x1.5xx
1987xM20x1.5xx
1988xM20x1.5xx
1989xM20x1.5xx
1990xM20x1.5xx
1991xM20x1.5xx
1992xM20x1.5xx
1993xM20x1.5xx

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.