Sizes of wheel nuts of Geely SC7

home ⇒ equipment ⇒ wheel fastener

For the SC7 model, the wheel is attached to the hub using wheel nuts. The number of fasteners depends on the SC7 year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 4;
  • Fastener size: from M12x1.25 to M12x1.5;
  • Diameter of the mounting holes (PCD): 100;
  • Disc offset (ET): 54.10.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Honda
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 6from M12x1.25 to M14x1.5
Possible fastener sizes for all Honda vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
4M12x1.5114.364.10
5M12x1.5114.364.10
4M12x1.5114.356.10
4M12x1.510056.10
4M12x1.512056.10
4M12x1.2512067.10
4x114.355
4x114.350
5x114.355
5x114.350
4x10035
4x10045
5x114.339
5x114.345
4x10038
5x114.338
4x10055
6x139.738
4x10039
4M12x1.510045
5M14x1.5114.364.10
4x114.345
4M12x1.510054.10
5M12x1.5114.370.10
5M12x1.512064.10
5M14x1.512064.10
5x114.365
5x114.360
4M12x1.510040
6M12x1.5139.738
5M14x1.512055
xM12x1.5xx
4x10040
4M12x1.512067.10
5M12x1.5114.356.10
5x12055
4x114.360
5x114.348
5x114.3x
4M12x1.510051
4M12x1.510053
5M12x1.511267.10
5M12x1.5114.350
4M12x1.510050
4M12x1.5114.355
4M12x1.5114.350
5M12x1.5114.355
5M12x1.5114.345
5M12x1.511256.10
4M12x1.510042
4M12x1.510047
5M12x1.5114.348
5M12x1.5114.351
5M12x1.5114.353
5M12x1.5114.349
4M12x1.510035

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Honda by models:

0 Comments