Sizes of wheel nuts of Hummer H3

home ⇒ equipment ⇒ wheel fastener

For the H3 model, the wheel is attached to the hub using wheel nuts. The number of fasteners depends on the H3 year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 6;
  • Fastener size: M12x1.5;
  • Diameter of the mounting holes (PCD): 139.7;
  • Disc offset (ET): 100.10.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Hyundai
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 6M12x1.5
Possible fastener sizes for all Hyundai vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
5x114.347
6M12x1.5139.792.50
5x114.350
6x139.756
6x139.750
5x12040
6x139.656
5x12041
5M12x1.5114.367.10
4M12x1.510054.10
4M12x1.5114.367.10
6M12x1.5139.7108.00
5x114.346
4x114.346
4x114.340
4x114.338
4x114.335
5M12x1.5114.349.5
xM12x1.5xx
6M12x1.5139.7106.20
5x114.340
4x10046
6M12x1.5139.740
6M12x1.5139.746
5M12x1.512067.10
5M12x1.5114.353
5M12x1.5114.350
5M12x1.5114.351
5M12x1.5114.344
5M12x1.5114.352
4M12x1.510041
4M12x1.510043
4M12x1.510046
4M12x1.510047
4M12x1.510050
5M12x1.5114.346
5M12x1.5114.355
5M12x1.5114.340
5M12x1.5114.347
5M12x1.5114.354
4M12x1.510040
4M12x1.510048
5M12x1.5120x
4M12x1.510052
5M12x1.5114.3x
5M12x1.5114.348
4M12x1.5100x
4M12x1.510049

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Hyundai by models:

0 Comments