Sizes of wheel гаек of Isuzu MU-X

For the MU-X model, the wheel is attached to the hub using wheel гаек. The number of fasteners depends on the MU-X year of manufacture and is presented in the table below.

Total dimensions of fasteners:

  • Number of fasteners: 6 (units);
  • Fastener size: from M12x1.5 to M14x1.5;
  • Diameter of the mounting holes (PCD): 139.7 (mm);
  • Disc offset (ET): from 28 (mm) to 38 (mm).

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).



General parameters of wheel гаек of Isuzu MU-X
General view spravkaGeneral view wheel fastener Quantity (units) spravka
Number of fasteners per hub for Isuzu model.

Dimensions (mm) spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
General view spravka
Type of wheel fastener:

For fastening of wheels or discs, 2 main types of fasteners are used:

-wheel bolts;
-wheel nuts.

Dimensions гаек
(чертеж гаек)
6 (units) from M12x1.5 to M14x1.5 Гайка
Size tables of wheel гаек of Isuzu MU-X
Year Quantity (units) spravka
Number of fasteners per hub for Isuzu model.

Dimensions (mm) spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
PCD (mm) spravka
Diameter between fasteners:

Diameter of the circle on which the mounting holes are located for Isuzu model.

spravka
ET (mm) spravka
Disc offset:

1. The distance between the vertical plane of symmetry of the wheel and the plane of contact of the disk to the hub.

spravka
1.9 CRDi
20176M14x1.5139.728
20176M14x1.5139.733
20176M14x1.5139.738
20186M14x1.5139.728
20186M14x1.5139.733
20186M14x1.5139.738
20196M14x1.5139.728
20196M14x1.5139.733
20196M14x1.5139.738
2.5TD
20136M12x1.5139.733
20136M12x1.5139.735
20146M12x1.5139.733
20146M12x1.5139.735
20156M12x1.5139.733
20156M12x1.5139.735
20166M12x1.5139.733
20166M12x1.5139.735
20176M12x1.5139.733
20176M12x1.5139.735
3.0TD
20136M12x1.5139.730
20136M12x1.5139.733
20136M12x1.5139.735
20146M12x1.5139.730
20146M12x1.5139.733
20146M12x1.5139.735
20156M12x1.5139.730
20156M12x1.5139.733
20156M12x1.5139.735
20166M12x1.5139.730
20166M12x1.5139.733
20166M12x1.5139.735
20176M12x1.5139.730
20176M12x1.5139.733
20176M12x1.5139.735
3.0 CRDi
20176M14x1.5139.728
20176M14x1.5139.733
20176M14x1.5139.738
20186M14x1.5139.728
20186M14x1.5139.733
20186M14x1.5139.738
20196M14x1.5139.728
20196M14x1.5139.733
20196M14x1.5139.738

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.