Sizes of wheel болтов of Lancia Kappa Coupe

For the Kappa Coupe model, the wheel is attached to the hub using wheel болтов. The number of fasteners depends on the Kappa Coupe year of manufacture and is presented in the table below.

Total dimensions of fasteners:

  • Number of fasteners: 4 (units);
  • Fastener size: -;
  • Diameter of the mounting holes (PCD): 98 (mm);
  • Disc offset (ET): 32 (mm).

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).



General parameters of wheel болтов of Lancia Kappa Coupe
General view spravkaGeneral view wheel fastener Quantity (units) spravka
Number of fasteners per hub for Lancia model.

Dimensions (mm) spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
General view spravka
Type of wheel fastener:

For fastening of wheels or discs, 2 main types of fasteners are used:

-wheel bolts;
-wheel nuts.

Dimensions болтов
(чертеж болтов)
4 (units) - Болт
Size tables of wheel болтов of Lancia Kappa Coupe
Year Quantity (units) spravka
Number of fasteners per hub for Lancia model.

Dimensions (mm) spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
PCD (mm) spravka
Diameter between fasteners:

Diameter of the circle on which the mounting holes are located for Lancia model.

spravka
ET (mm) spravka
Disc offset:

1. The distance between the vertical plane of symmetry of the wheel and the plane of contact of the disk to the hub.

spravka
Lancia Kappa Coupe 2.0 16V Turbo
19964x9832
19964x9832
19964x9832
19964x9832
19974x9832
19974x9832
19974x9832
19974x9832
19984x9832
19984x9832
19984x9832
19984x9832
19994x9832
19994x9832
19994x9832
19994x9832
20004x9832
20004x9832
20004x9832
20004x9832
20014x9832
20014x9832
20014x9832
20014x9832
Lancia Kappa Coupe 2.0 20V
19964x9832
19964x9832
19964x9832
19964x9832
19974x9832
19974x9832
19974x9832
19974x9832
19984x9832
19984x9832
19984x9832
19984x9832
19994x9832
19994x9832
19994x9832
19994x9832
20004x9832
20004x9832
20004x9832
20004x9832
20014x9832
20014x9832
20014x9832
20014x9832
Lancia Kappa Coupe 2.0 20V Turbo
19984x9832
19984x9832
19984x9832
19984x9832
19994x9832
19994x9832
19994x9832
19994x9832
20004x9832
20004x9832
20004x9832
20004x9832
20014x9832
20014x9832
20014x9832
20014x9832
Lancia Kappa Coupe 2.4 20V
19964x9832
19964x9832
19964x9832
19964x9832
19974x9832
19974x9832
19974x9832
19974x9832
19984x9832
19984x9832
19984x9832
19984x9832
19994x9832
19994x9832
19994x9832
19994x9832
20004x9832
20004x9832
20004x9832
20004x9832
20014x9832
20014x9832
20014x9832
20014x9832
Lancia Kappa Coupe 3.0 24V
19964x9832
19964x9832
19964x9832
19964x9832
19974x9832
19974x9832
19974x9832
19974x9832
19984x9832
19984x9832
19984x9832
19984x9832
19994x9832
19994x9832
19994x9832
19994x9832
20004x9832
20004x9832
20004x9832
20004x9832
20014x9832
20014x9832
20014x9832
20014x9832
Lancia Kappa Coupe 838 2.0 16V Turbo
20014x9832
20014x9832
20014x9832
20014x9832

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.