Sizes of wheel болтов of LDV Convoy

For the Convoy model, the wheel is attached to the hub using wheel болтов. The number of fasteners depends on the Convoy year of manufacture and is presented in the table below.

Total dimensions of fasteners:

  • Number of fasteners: -;
  • Fastener size: M12x1.5;
  • Diameter of the mounting holes (PCD): -;
  • Disc offset (ET): -.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).



General parameters of wheel болтов of LDV Convoy
General view spravkaGeneral view wheel fastener Quantity (units) spravka
Number of fasteners per hub for LDV model.

Dimensions (mm) spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
General view spravka
Type of wheel fastener:

For fastening of wheels or discs, 2 main types of fasteners are used:

-wheel bolts;
-wheel nuts.

Dimensions болтов
(чертеж болтов)
- M12x1.5 Болт
Size tables of wheel болтов of LDV Convoy
Year Quantity (units) spravka
Number of fasteners per hub for LDV model.

Dimensions (mm) spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

spravka
PCD (mm) spravka
Diameter between fasteners:

Diameter of the circle on which the mounting holes are located for LDV model.

spravka
ET (mm) spravka
Disc offset:

1. The distance between the vertical plane of symmetry of the wheel and the plane of contact of the disk to the hub.

spravka
2.5 DI
1988xM12x1.5xx
1989xM12x1.5xx
1990xM12x1.5xx
1991xM12x1.5xx
1992xM12x1.5xx
1993xM12x1.5xx
1994xM12x1.5xx
1995xM12x1.5xx
1996xM12x1.5xx
1997xM12x1.5xx
1998xM12x1.5xx
1999xM12x1.5xx
2000xM12x1.5xx
2001xM12x1.5xx
2002xM12x1.5xx
2003xM12x1.5xx
2004xM12x1.5xx
2005xM12x1.5xx
2006xM12x1.5xx
2007xM12x1.5xx
2008xM12x1.5xx
2009xM12x1.5xx
2.5 TDI
1988xM12x1.5xx
1989xM12x1.5xx
1990xM12x1.5xx
1991xM12x1.5xx
1992xM12x1.5xx
1993xM12x1.5xx
1994xM12x1.5xx
1995xM12x1.5xx
1996xM12x1.5xx
1997xM12x1.5xx
1998xM12x1.5xx
1999xM12x1.5xx
2000xM12x1.5xx
2001xM12x1.5xx
2002xM12x1.5xx
2003xM12x1.5xx
2004xM12x1.5xx
2005xM12x1.5xx
2006xM12x1.5xx
2007xM12x1.5xx
2008xM12x1.5xx
2009xM12x1.5xx

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.