Sizes of Mazda wheel fastener - Dimension tables

Sizes of wheel fasteners of Ford Mondeo ST220

For the Mondeo ST220 model, the wheel is attached to the hub using wheel fasteners. The number of fasteners depends on the Mondeo ST220 year of manufacture and is presented in the table below.

Total dimensions of fasteners:

Number of fasteners: 5;
Fastener size: -;
Diameter of the mounting holes (PCD): 108;
Disc offset (ET): -.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing

General parameters of wheel fastener for Mazda

General view General view	N Number of fasteners per hub for marka. Measured in pieces.	Size Metric size of fasteners: Thread M14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.
(General view)	-	from 4 to 6	from M12x1.25 to M12x1.75

Possible fastener sizes for all Mazda vehicles

N Number of fasteners per hub for marka. Measured in pieces.	Size Metric size of fasteners: ThreadM14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.	ET (mm) Disc offset: Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.
x	M12x1.5	x	x
4	x	108	43
4	M12x1.5	100	54.10
4	M12x1.5	108	54.10
4	M12x1.5	108	63.30
5	M12x1.5	114.3	67.10
5	M12x1.5	112	67.10
4	M12x1.5	100	67.10
5	x	114.3	55
5	x	114.3	50
5	x	114.3	60
5	x	114.3	45
5	x	114.3	38
5	x	114.3	52
5	M12x1.5	114.3	60.10
4	M12x1.5	114.3	60.10
4	M12x1.5	110	60.10
4	M12x1.5	114.3	67.10
4	M12x1.5	120	45
4	M12x1.5	120	50
4	M12x1.5	120	55
4	x	100	45
5	M12x1.25	139.7	20
5	M12x1.25	139.7	22
5	M12x1.25	139.7	25
4	x	100	50
6	M12x1.5	139.7	108.00
6	M12x1.5	139.7	94.00
5	x	114.3	40
6	x	139.7	40
5	M12x1.5	114.3	40
6	M12x1.5	139.7	93.10
5	x	114.3	42
5	M12x1.5	114.3	50
5	M12x1.5	114.3	48
5	M12x1.5	114.3	45
5	M12x1.75	114.3	50
5	M12x1.75	114.3	48
5	M12x1.75	114.3	55
5	M12x1.5	114.3	52
4	x	100	40
5	M12x1.5	114.3	54.10
5	M12x1.5	139.7	25
5	M12x1.5	139.7	20
5	M12x1.5	139.7	30
6	M12x1.5	139.7	35
6	M12x1.5	139.7	40
6	M12x1.5	139.7	30
4	M12x1.5	100	45
4	M12x1.5	100	42
4	M12x1.5	100	38
4	x	100	38
5	x	114.3	35
5	x	139.7	22
4	M12x1.5	114.3	45
4	M12x1.5	114.3	38
4	M12x1.5	114.3	42
4	x	108	50
4	x	108	40
6	M12x1.5	139.7	10
6	M12x1.5	139.7	12
4	x	114.3	45
5	x	139.7	25
6	x	139.7	30
5	M12x1.5	114.3	42
4	M12x1.5	114.3	44
4	M12x1.5	100	40
6	M12x1.5	139.7	44
6	M12x1.5	139.7	38
5	M12x1.5	114.3	52.5
5	M12x1.5	112	54.10
4	M12x1.5	114.3	35
4	M12x1.5	114.3	40
4	M12x1.5	114.3	50
4	M12x1.5	100	50
4	M12x1.5	100	35
4	M12x1.25	100	40
5	M12x1.5	114.3	55
6	M12x1.5	139.7	15

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Mazda by models:

0 Comments