Sizes of wheel bolts of Mercedes-Benz Sprinter

home ⇒ equipment ⇒ wheel fastener ⇒ mercedes-benz

For the Sprinter model, the wheel is attached to the hub using wheel bolts. The number of fasteners depends on the Sprinter year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: from 5 to 6;
  • Fastener size: M14x1.5;
  • Diameter of the mounting holes (PCD): 130;
  • Disc offset (ET): 84.10.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel bolts of Mercedes-Benz Sprinter
General view spravka
General view

N spravka
Number of fasteners per hub for Mercedes-Benz Sprinter.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions bolts

(General view)		from 5 to 6M14x1.5130
Size tables of wheel bolts of Mercedes-Benz Sprinter
Years spravka
Year of manufacture or modification of the Sprinter

n spravka
Number of fasteners per hub for Mercedes-Benz Sprinter.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 - thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
213 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
216
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
216 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
219 BlueTEC
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
310 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
313 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
316
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
316 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
316 NTG
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
319 BlueTEC
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
413 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
416 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
510 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
513 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
516
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
516 CDI
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
516 NTG
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
519 BlueTEC
20166M14x1.513084.10
20156M14x1.513084.10
20146M14x1.513084.10
20136M14x1.513084.10
209-518
20126M14x1.513084.10
20116M14x1.513084.10
20106M14x1.513084.10
20096M14x1.513084.10
20086M14x1.513084.10
20076M14x1.513084.10
211-215-311-315-224-324
20076M14x1.513084.10
20065M14x1.513084.10
20055M14x1.513084.10
20045M14x1.513084.10
20035M14x1.513084.10
216-316
20025M14x1.513084.10
20015M14x1.513084.10
20005M14x1.513084.10

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.


0 Comments