Sizes of wheel bolts of Mercedes-Benz W124

home ⇒ equipment ⇒ wheel fastener

For the W124 model, the wheel is attached to the hub using wheel bolts. The number of fasteners depends on the W124 year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 5;
  • Fastener size: M12x1.5;
  • Diameter of the mounting holes (PCD): 112;
  • Disc offset (ET): 66.60.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Mitsubishi
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 4 to 6from 12x1.5 to M12x1.5
Possible fastener sizes for all Mitsubishi vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
5M12x1.5114.367.10
5x114.346
4x114.346
4M12x1.5114.367.10
xM12x1.5xx
6M12x1.5139.767.10
4M12x1.5114.346
4M12x1.510056.10
5M12x1.5114.3107.00
4M12x1.510046
4M12x1.510038
4x10046
4x10038
5x114.338
5M12x1.5114.3x
5M12x1.5139.70
5M12x1.5139.717
6M12x1.5139.7108.00
4M12x1.5100x
4M12x1.510067.10
5M12x1.5114.356.10
4M12x1.5114.356.10
5M12x1.511260.10
5M12x1.5114.367.00
5M12x1.511256.10
5M12x1.5114.346
5M12x1.5114.338
5x114.3x
4M12x1.5114.342
5M12x1.5114.393.00
6M12x1.5139.793.00
4M12x1.5114.318
4M12x1.5114.315
6x139.720
6x139.735
6x139.730
6x139.7x
6x139.738
5x114.318
5x114.345
5x114.335
6x139.710
4x10040
512x1.5114.367.1
4x114.338
6M12x1.25139.7100.00
6x139.75
4x114.345
512x1.5114.335
4M12x1.5114.344
5M12x1.5114.348
5M12x1.5114.340
6M12x1.5139.710
6M12x1.5139.725
6M12x1.5139.730
5M12x1.5114.342
6M12x1.5139.733
6M12x1.5139.735
6M12x1.5139.720
6M12x1.5139.722
4M12x1.25114.340
4M12x1.25114.345
5M12x1.5114.345
5M12x1.5114.350
5M12x1.5114.344
4M12x1.5114.348
4M12x1.510054.10
4M12x1.25114.366.10
6M12x1.5139.738
xM12.5xx
5M12x1.511267.10

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Mitsubishi by models:

0 Comments