Sizes of wheel bolts of Porsche Panamera

home ⇒ equipment ⇒ wheel fastener

For the Panamera model, the wheel is attached to the hub using wheel bolts. The number of fasteners depends on the Panamera year of manufacture and is presented in the table below.

Total dimensions of fasteners:
  • Number of fasteners: 5;
  • Fastener size: M14x1.5;
  • Diameter of the mounting holes (PCD): 130;
  • Disc offset (ET): 71.60.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.
Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing
General parameters of wheel fastener for Renault
General view spravka
General view

N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

Thread M14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

Dimensions wheel fastener

(General view)		-from 3 to 6from 12x1.5 to M14x1.5
Possible fastener sizes for all Renault vehicles
N spravka
Number of fasteners per hub for marka.

Measured in pieces.

Size spravka
Metric size of fasteners:

ThreadM14 x 1.5 means:

M14 - thread diameter 14 (mm);
1.5 thread pitch (distance between adjacent threads).

PCD (mm) spravka
Disc drilling:

1. Number of bolt holes.

2. Diameter of the circle on which the mounting holes are located.

spravka

ET (mm) spravka
Disc offset:

Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.

spravka
xM12x1.5xx
4x10040
412x1.510045
5M12x1.510860.10
4M12x1.510060.10
4M12x1.510066.10
4M14x1.510060.10
5M14x1.510860.10
5M12x1.5114.366.10
5M14x1.5114.366.10
4M12x1.510036
4M12x1.510040
5M12x1.25114.366.10
5M14x1.510866.10
5M12x1.510866.10
5M14x1.5114.371.10
5M14x1.511871.10
3M12x1.511260.10
6M14x1.520089.10
6M14x1.5200142.00
xM12x1.25xx
6M12x1.25114.366.10
4x10036
4x10043
4x10038
5x10838
4x10050
5x10868
5x1086
5x10820
5x10840
5x10850
5x10845
5x10844
4x10030
5x114.347
5M14x1.517066
5M14x1.517058
5x13066
4x10045
4x10049
5x10836
5x10849
5x114.343
5x114.349
5x114.335
5x10842
4x10035
5x10843
5x114.345
5x11850
5M14x1.5114.350
5M14x1.5114.345
3M12x1.510037
4M12x1.2510060.10
4M12x1.25114.366.10
5M12x1.5114.350
5M12x1.5114.342
5M12x1.5114.347
5M12x1.5114.349
5M12x1.5114.343
5M12x1.5114.345
5M14x1.5114.347
4M12x1.510048
4M12x1.510050
5M12x1.510850
5M12x1.510848
5M14x1.513066
6M14x1.5200100
6M14x1.5200110
5M14x1.511850
5M14x1.510848
5M14x1.510850
4M12x1.510045
5M12x1.25114.347
5M12x1.25114.350
5M12x1.5114.333
4M12x1.510043
4M12x1.510038
4M12x1.510041

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Wheel fastener Renault by models:

0 Comments