Sizes of wheel fasteners of ZAZ Chance

home ⇒ equipment ⇒ wheel fastener ⇒ zaz

For the Chance model, the wheel is attached to the hub using wheel fasteners. The number of fasteners depends on the Chance year of manufacture and is presented in the table below.

Total dimensions of fasteners:

Number of fasteners: 4;
Fastener size: -;
Diameter of the mounting holes (PCD): 100;
Disc offset (ET): 49.

Important: the above data are limits for all vehicle modifications, specific figures depend on the year of manufacture.

Rules for selecting wheel fasteners:

Different wheel fasteners are often used for cast and stamped disks - this applies to the length of the bolts, since the thickness of different types of disks can vary significantly.

When selecting any fasteners, special attention should be paid to the thread pitch. This parameter is always indicated after the “x” in the marking.

Most of the wheel fasteners have metric threads with fine pitch (М12х1.25/М12х1.5/М14х1.25/М14х1.5), which must correspond to the threads of thread studs or threaded holes in the wheel hub.

Important: the marking of fastener bolt M12x1.5 is deciphered as follows: thread with a nominal diameter of 12 (mm), thread pitch 1.5 (mm).

Wheel fastener - full drawing

General parameters of wheel fasteners of ZAZ Chance

General view General view	N Number of fasteners per hub for ZAZ Chance.	Size Metric size of fasteners: Thread M14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 - thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.
(General view)	4	-	100

Size tables of wheel fasteners of ZAZ Chance

Years Year of manufacture or modification of the Chance	n Number of fasteners per hub for ZAZ Chance.	Size Metric size of fasteners: ThreadM14 x 1.5 means: M14 - thread diameter 14 (mm); 1.5 - thread pitch (distance between adjacent threads).	PCD (mm) Disc drilling: 1. Number of bolt holes. 2. Diameter of the circle on which the mounting holes are located.	ET (mm) Disc offset: Distance between the vertical plane of symmetry of the wheel and the plane of contact of the disc to the hub.
ZAZ Chance 1.3
2004	4	x	100	49
2005	4	x	100	49
2006	4	x	100	49
2007	4	x	100	49
2008	4	x	100	49
2009	4	x	100	49
2010	4	x	100	49
2011	4	x	100	49
2012	4	x	100	49
2013	4	x	100	49
2014	4	x	100	49
2015	4	x	100	49
2016	4	x	100	49
2017	4	x	100	49
2018	4	x	100	49
ZAZ Chance 1.4
2011	4	x	100	49
2012	4	x	100	49
2013	4	x	100	49
2014	4	x	100	49
2015	4	x	100	49
2016	4	x	100	49
2017	4	x	100	49
2018	4	x	100	49
ZAZ Chance 1.5
2009	4	x	100	49
2010	4	x	100	49
2011	4	x	100	49
2012	4	x	100	49
2013	4	x	100	49
2014	4	x	100	49
2015	4	x	100	49
2016	4	x	100	49
2017	4	x	100	49
2018	4	x	100	49
ZAZ Chance 1.5i
2010	4	x	100	49
2011	4	x	100	49
2012	4	x	100	49
2013	4	x	100	49
2014	4	x	100	49
2015	4	x	100	49
2016	4	x	100	49
2017	4	x	100	49

Warning: the above data are official figures of the manufacturers, however, it should be borne in mind that the information is for reference and does not guarantee unambiguous accuracy.

Other parameters ZAZ Chance:

0 Comments